河南app手机网站制作,昆明官网优化公司,用c 做毕业设计的音乐网站,dw做的静态网站怎么分享链接文章目录 K8S Deployment HA1.机器规划2.前期准备2.1 安装ansible2.2 修改 hostname2.3 配置免密2.4 时间同步2.5 系统参数调整2.6 安装 Docker2.7 部署 HaproxyKeepalived 3. 部署 K8S3.1 安装 k8s命令3.2 k8s初始化3.3 添加其他master节点3.4 添加 Node节点3.5 安装 CNI3.6 查… 文章目录 K8S Deployment HA1.机器规划2.前期准备2.1 安装ansible2.2 修改 hostname2.3 配置免密2.4 时间同步2.5 系统参数调整2.6 安装 Docker2.7 部署 HaproxyKeepalived 3. 部署 K8S3.1 安装 k8s命令3.2 k8s初始化3.3 添加其他master节点3.4 添加 Node节点3.5 安装 CNI3.6 查看pod状态3.7 配置IPVS K8S Deployment HA
1.机器规划
IP主机名角色10.83.195.6master1master10.83.195.7master2master10.83.195.8master3master10.83.195.9node1node10.83.195.10node2node10.83.195.250VIP
2.前期准备
2.1 安装ansible
# master1节点
yum install -y ansible2.2 修改 hostname
# 修改hostname
hostnamectl set-hostname xxx# 配置hosts
# 127.0.0.1 localhost xxx ::1 localhost6xxx 需要保留否则calico pod会报错
ansible -i /opt/ansible/nodes all -m shell -a cat /etc/hostsEOF
127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4
::1 localhost6 localhost6.localdomain6 localhost6.localdomain
10.83.195.6 master1
10.83.195.7 master2
10.83.195.8 master3
10.83.195.9 node1
10.83.195.10 node2
EOF2.3 配置免密
# 生成ssh密钥对
ssh-keygen # root免密
ansible -i /opt/ansible/nodes all -m shell -a sudo sed -i s/PermitRootLogin no/PermitRootLogin yes/ /etc/ssh/sshd_config sudo grep PermitRootLogin /etc/ssh/sshd_config sudo systemctl restart sshd# master1 ssh-copy-id
ssh-copy-id 10.83.195.6
# 可以把 maste1的公私钥 拷贝到 master2、3节点方便免密2.4 时间同步
ansible -i /opt/ansible/nodes all -m shell -a yum install chrony -y
ansible -i /opt/ansible/nodes all -m shell -a systemctl start chronyd systemctl enable chronyd chronyc sources2.5 系统参数调整
# 临时关闭关闭swap主要是为了性能考虑
# 通过free命令查看swap是否关闭
ansible -i /opt/ansible/nodes all -m shell -a sudo swapoff -a free# 永久关闭
ansible -i /opt/ansible/nodes all -m shell -a sudo sed -i s/.*swap.*/#/ /etc/fstab# 禁用SELinux
# 临时关闭
ansible -i /opt/ansible/nodes all -m shell -a setenforce 0
# 永久禁用
ansible -i /opt/ansible/nodes all -m shell -a sed -i s/^SELINUXenforcing$/SELINUXdisabled/ /etc/selinux/config# 关闭防火墙
ansible -i /opt/ansible/nodes all -m shell -a systemctl stop firewalld systemctl disable firewalld# 允许 iptables 检查桥接流量
ansible -i /opt/ansible/nodes all -m shell -a sudo modprobe br_netfilter lsmod | grep br_netfilteransible -i /opt/ansible/nodes all -m shell -a sudo cat EOF | sudo tee /etc/modules-load.d/k8s.conf
overlay
br_netfilter
EOFansible -i /opt/ansible/nodes all -m shell -a sudo modprobe overlay sudo modprobe br_netfilter# 设置所需的 sysctl 参数参数在重新启动后保持不变
ansible -i /opt/ansible/nodes all -m shell -a sudo cat EOF | sudo tee /etc/sysctl.d/k8s.conf
net.bridge.bridge-nf-call-iptables 1
net.bridge.bridge-nf-call-ip6tables 1
net.ipv4.ip_forward 1
EOFansible -i /opt/ansible/nodes all -m shell -a echo 1|sudo tee /proc/sys/net/ipv4/ip_forward# 应用 sysctl 参数而不重新启动
ansible -i /opt/ansible/nodes all -m shell -a sudo sysctl --system2.6 安装 Docker
# centos7
ansible -i /opt/ansible/nodes all -m shell -a wget -O /etc/yum.repos.d/CentOS-Base.repo http://mirrors.aliyun.com/repo/Centos-7.repo# centos8
# wget -O /etc/yum.repos.d/CentOS-Base.repo http://mirrors.aliyun.com/repo/Centos-8.repo# 安装yum-config-manager配置工具
ansible -i /opt/ansible/nodes all -m shell -a sudo yum -y install yum-utils
# 设置yum源
ansible -i /opt/ansible/nodes all -m shell -a sudo yum-config-manager --add-repo http://mirrors.aliyun.com/docker-ce/linux/centos/docker-ce.repo# 软链修改docker镜像存储目录
ansible -i /opt/ansible/nodes all -m shell -a sudo mkdir /data/docker sudo ln -s /data/docker /var/lib/docker# 安装docker-ce版本
ansible -i /opt/ansible/nodes all -m shell -a sudo yum install -y docker-ce
# 自启、启动
ansible -i /opt/ansible/nodes all -m shell -a sudo systemctl start docker sudo systemctl enable docker sudo docker --version# 查看版本号
# sudo docker --version
# 查看版本具体信息
# sudo docker version# 修改Docker镜像源设置
# 修改文件 /etc/docker/daemon.json没有这个文件就创建
ansible -i /opt/ansible/nodes all -m shell -a sudo cat EOF | sudo tee /etc/docker/daemon.json
{registry-mirrors: [https://ogeydad1.mirror.aliyuncs.com],exec-opts: [native.cgroupdriversystemd]
}
EOF
# 重载、重启 docker
ansible -i /opt/ansible/nodes all -m shell -a sudo systemctl reload docker sudo systemctl restart docker sudo systemctl status docker2.7 部署 HaproxyKeepalived
K8S Master HA 通过 HaproxyKeepalived 实现
# 3个master节点上执行
ansible -i /opt/ansible/nodes master -m shell -a yum install keepalived haproxy -y修改 haproxy.cfg配置
# vim /etc/haproxy/haproxy.cfg 追加如下配置
frontend k8s-masterbind 0.0.0.0:16443mode tcpoption tcplogtcp-request inspect-delay 5sdefault_backend k8s-masterbackend k8s-mastermode tcpoption tcplogoption tcp-checkbalance roundrobindefault-server inter 10s downinter 5s rise 2 fall 2 slowstart 60s maxconn 250 maxqueue 256 weight 100server master1 10.83.195.6:6443 check inter 10000 fall 2 rise 2 weight 100server master2 10.83.195.7:6443 check inter 10000 fall 2 rise 2 weight 100server master3 10.83.195.8:6443 check inter 10000 fall 2 rise 2 weight 100# 分发到其他master
ansible -i /opt/ansible/nodes master -m copy -a src/etc/haproxy/haproxy.cfg dest/etc/haproxy/haproxy.cfg修改keepalived.conf配置
# vim /etc/keepalived/keepalived.conf 替换内容
# state: 主节点为MASTER从节点为BACKUP
# interface: ifconfig 查看网卡名
# priority: MASTER使用101BACKUP使用100# master
! Configuration File for keepalived
global_defs {script_user rootenable_script_securityrouter_id LVS_DEVEL
}
vrrp_script check_apiserver {script /etc/keepalived/check_k8s.shinterval 3weight -2fall 2rise 2
}vrrp_instance VI_1 {# 主节点为MASTER从节点为BACKUPstate MASTER# 网卡名interface ens192virtual_router_id 51# MASTER当中使用101BACKUP当中使用100priority 101authentication {auth_type PASSauth_pass admin}virtual_ipaddress {# VIP10.83.195.250}track_script {check_k8s}
}# backup
! Configuration File for keepalived
global_defs {router_id LVS_DEVEL
}
vrrp_script check_apiserver {script /etc/keepalived/check_k8s.shinterval 3weight -2fall 2rise 2
}vrrp_instance VI_1 {# 主节点为MASTER从节点为BACKUPstate BACKUP# 网卡名interface ens192virtual_router_id 51# MASTER当中使用101BACKUP当中使用100priority 100authentication {auth_type PASSauth_pass admin}virtual_ipaddress {# VIP10.83.195.250}track_script {check_k8s}
}检测脚本 check_k8s.sh
#!/bin/bashfunction check_k8s() {for ((i0;i5;i));doapiserver_pid_id$(pgrep kube-apiserver)if [[ ! -z $apiserver_pid_id ]];thenreturnelsesleep 2fiapiserver_pid_id0done
}# 1:running 0:stopped
check_k8s
if [[ $apiserver_pid_id -eq 0 ]];then/usr/bin/systemctl stop keepalivedexit 1
elseexit 0
fi# 分发
ansible -i /opt/ansible/nodes master -m copy -a src/etc/keepalived/check_k8s.sh dest/etc/keepalived/
ansible -i /opt/ansible/nodes master -m shell -a chmod x /etc/keepalived/check_k8s.sh# 启动
ansible -i /opt/ansible/nodes master -m shell -a systemctl enable --now keepalived haproxy# 查看VIP
ip a3. 部署 K8S
3.1 安装 k8s命令
# 所有节点
ansible -i /opt/ansible/nodes all -m shell -a sudo cat EOF | sudo tee /etc/yum.repos.d/kubernetes.repo
[k8s]
namek8s
enabled1
gpgcheck0
baseurlhttps://mirrors.aliyun.com/kubernetes/yum/repos/kubernetes-el7-x86_64/
EOF
# disableexcludeskubernetes禁掉除了这个kubernetes之外的别的仓库
ansible -i /opt/ansible/nodes all -m shell -a yum install -y kubelet-1.23.6 kubeadm-1.23.6 kubectl-1.23.6 --disableexcludeskubernetes# 查看k8s版本
# sudo kubectl version命令 会报错正常 Unable to connect to the server: dial tcp: lookup localhost on 10.82.26.252:53: no such host
ansible -i /opt/ansible/nodes all -m shell -a sudo kubectl version sudo yum info kubeadm# 设置为开机自启并现在立刻启动服务 --now立刻启动服务
ansible -i /opt/ansible/nodes all -m shell -a sudo systemctl enable --now kubelet sudo systemctl status kubelet3.2 k8s初始化
# master1 节点执行
# --control-plane-endpoint VIP:16443
# --pod-network-cidr192.168.0.0/16 需要与calico.yaml 文件中的 CALICO_IPV4POOL_CIDR 配置网段一致
kubeadm init --image-repository registry.aliyuncs.com/google_containers --kubernetes-version v1.23.6 --pod-network-cidr192.168.0.0/16 --control-plane-endpoint 10.83.195.250:16443 --upload-cert# Your Kubernetes control-plane has initialized successfully!# To start using your cluster, you need to run the following as a regular user:# mkdir -p $HOME/.kube
# sudo cp -i /etc/kubernetes/admin.conf $HOME/.kube/config
# sudo chown $(id -u):$(id -g) $HOME/.kube/config# Alternatively, if you are the root user, you can run:# export KUBECONFIG/etc/kubernetes/admin.conf# You should now deploy a pod network to the cluster.
# Run kubectl apply -f [podnetwork].yaml with one of the options listed at:
# https://kubernetes.io/docs/concepts/cluster-administration/addons/# You can now join any number of the control-plane node running the following command on each as root:# kubeadm join 10.83.195.250:16443 --token 6z1jge.6hue81vruwh8msdl \
# --discovery-token-ca-cert-hash sha256:a3db8061e0b570e897b2d0e7c243ef7342c51299d04ef649737187e50aee8ea6 \
# --control-plane --certificate-key 35e73eae794acd9275445902cfd8d545a0e3b8e017f8d5960bd2e6796f74c386# Please note that the certificate-key gives access to cluster sensitive data, keep it secret!
# As a safeguard, uploaded-certs will be deleted in two hours; If necessary, you can use
# kubeadm init phase upload-certs --upload-certs to reload certs afterward.# Then you can join any number of worker nodes by running the following on each as root:# kubeadm join 10.83.195.250:16443 --token 6z1jge.6hue81vruwh8msdl \
# --discovery-token-ca-cert-hash sha256:a3db8061e0b570e897b2d0e7c243ef7342c51299d04ef649737187e50aee8ea63.3 添加其他master节点
# You can now join any number of the control-plane node running the following command on each as root:kubeadm join 10.83.195.250:16443 --token 6z1jge.6hue81vruwh8msdl \--discovery-token-ca-cert-hash sha256:a3db8061e0b570e897b2d0e7c243ef7342c51299d04ef649737187e50aee8ea6 \--control-plane --certificate-key 35e73eae794acd9275445902cfd8d545a0e3b8e017f8d5960bd2e6796f74c386# 3个master节点
# 临时生效退出当前窗口重连环境变量失效
export KUBECONFIG/etc/kubernetes/admin.conf
# 永久生效推荐
echo export KUBECONFIG/etc/kubernetes/admin.conf ~/.bash_profile source ~/.bash_profile# 重新部署
# kubeadm reset
# rm -rf $HOME/.kube rm -rf /etc/cni/net.d rm -rf /etc/kubernetes/*
# 再执行kubeadm init 命令3.4 添加 Node节点
# Then you can join any number of worker nodes by running the following on each as root:
# kubeadm token create --print-join-commandkubeadm join 10.83.195.250:16443 --token 6z1jge.6hue81vruwh8msdl \--discovery-token-ca-cert-hash sha256:a3db8061e0b570e897b2d0e7c243ef7342c51299d04ef649737187e50aee8ea63.5 安装 CNI
# master1 节点
# kubectl apply -f https://raw.githubusercontent.com/coreos/flannel/master/Documentation/kube-flannel.yml# master1节点执行
# 下载 calico 配置文件可能会网络超时
curl https://docs.projectcalico.org/manifests/calico.yaml -O # 生成重定向链接
curl https://calico-v3-25.netlify.app/archive/v3.25/manifests/calico.yaml -O
kubectl apply -f calico.yaml# 修改 calico.yaml 文件中的 CALICO_IPV4POOL_CIDR 配置修改为与初始化的 cidr 相同
# 修改 IP_AUTODETECTION_METHOD 下的网卡名称
# 删除镜像 docker.io/ 前缀避免下载过慢导致失败
# sed -i s#docker.io/##g calico.yaml3.6 查看pod状态
kubectl get pods -A3.7 配置IPVS
解决集群内无法ping通ClusterIP或ServiceName
# 加载ip_vs相关内核模块
ansible -i /opt/ansible/nodes all -m shell -a sudo modprobe -- ip_vs sudo modprobe -- ip_vs_sh sudo sudo modprobe -- ip_vs_rr sudo modprobe -- ip_vs_wrr sudo modprobe -- nf_conntrack_ipv4# 验证开启ipvs
ansible -i /opt/ansible/nodes all -m shell -a sudo lsmod |grep ip_vs# 安装ipvsadm工具
ansible -i /opt/ansible/nodes all -m shell -a sudo yum install ipset ipvsadm -y# 编辑kube-proxy配置文件mode修改成ipvs
kubectl edit configmap -n kube-system kube-proxy# 先查看
kubectl get pod -n kube-system | grep kube-proxy
# delete让它自拉起
kubectl get pod -n kube-system | grep kube-proxy |awk {system(kubectl delete pod $1 -n kube-system)}
# 再查看
kubectl get pod -n kube-system | grep kube-proxy# 查看ipvs转发规则
ipvsadm -Ln
